Front/Rear Wishbones and Ball Joints

Rosco · 08-12-17, 09:32 PM

Hi, I am looking to replace and renew most of the running gear on my 1985 b2 Coupe quattro over the coming months.

From looking at part numbers it seems the Front and Rear Wishbones are the same? Can anyone confirm this?

https://epc.realoem.com/cat_spares/e...coq/61/046100/

If so I'll be ordering some Febi wishbones for around £28 each (alot cheaper and less time consuming than trying to clean the old ones up) 2 x FEBI 09527 & 2 x FEBI 09528

Now febi only list 2 different Ball Joints in their parts catalogue, so are the ball joints for front and rear the same? Should I order 2 x FEBI 01521 & 2 x FEBI 01522?

Thanks

mikes2 · 08-12-17, 10:07 PM

Wishbones for front and rear are the same for a 1985 car.

Ball joints are completely different though. Don't think Febi do the rear

quattrodave · 08-12-17, 11:09 PM

These are correct for the rear, other makes available just check on ebay

https://www.ebay.co.uk/itm/FIRST-LIN...sAAOSwevlaFvov

The balljoint mounts on the bottom of the strutt assembly and bolts into the adjustable bit on the wishbone, the wishbone bit looks like a front balljoint without a ball joint socket on the end just a tapered hole.

Colin Aitchison · 09-12-17, 09:26 AM

As far as I am aware the front wishbones fit the rear physical dimensions but the correct rear wishbones do not have an anti roll bar mount union fitted to them, they can be fitted upside down, look at the pressings in the wishbone for correct way up, been down the garage and found front and rear wishbones, photo below of near side wishbones front and rear, front wishbone has red circle with anti roll bar bush, green circle has bottom ball joint in it bending forward, notice rear wishbone, no welded in union for anti roll bar bush.

Photo below of under side of both wishbones, notice the pressing in the blue circle, I think this to let water drain out. sorry don't have a bottom ball joint link arm for rear wishbone but had a look below Ur quattro and it bends to the rear, more advice as if you need it, take photos of every thing as you dissemble it, yes it is a pain to do but if you take photos reassembling you will have before and after photos to post on the forum.

Rosco · 09-12-17, 11:02 AM

Thank you Dave and Colin for taking the time to reply, I nearly ordered the wrong ball joints. This forum is great!

Rosco · 10-12-17, 05:50 PM

Does anyone know if these rear ball joint carriers are available as new replacements?

Or Should I clean up my current ones?

08-12-17, 10:07 PM	#2
mikes2 4 ring whore! Classic Audi Club Member Join Date: Nov 2007 Location: Polmont Posts: 2,617	Wishbones for front and rear are the same for a 1985 car. Ball joints are completely different though. Don't think Febi do the rear __________________ 1991 90 quattro 20v sport 1991 90 quattro

08-12-17, 11:09 PM	#3
quattrodave Grown up member Classic Audi Club Member Join Date: Dec 2010 Location: Bingley Posts: 634	These are correct for the rear, other makes available just check on ebay https://www.ebay.co.uk/itm/FIRST-LIN...sAAOSwevlaFvov The balljoint mounts on the bottom of the strutt assembly and bolts into the adjustable bit on the wishbone, the wishbone bit looks like a front balljoint without a ball joint socket on the end just a tapered hole. Last edited by quattrodave; 08-12-17 at 11:12 PM.

09-12-17, 09:26 AM	#4
Colin Aitchison Senior Member Classic Audi Club Member Join Date: Dec 2013 Location: Back home in Tillicoultry Posts: 1,308	As far as I am aware the front wishbones fit the rear physical dimensions but the correct rear wishbones do not have an anti roll bar mount union fitted to them, they can be fitted upside down, look at the pressings in the wishbone for correct way up, been down the garage and found front and rear wishbones, photo below of near side wishbones front and rear, front wishbone has red circle with anti roll bar bush, green circle has bottom ball joint in it bending forward, notice rear wishbone, no welded in union for anti roll bar bush. Photo below of under side of both wishbones, notice the pressing in the blue circle, I think this to let water drain out. sorry don't have a bottom ball joint link arm for rear wishbone but had a look below Ur quattro and it bends to the rear, more advice as if you need it, take photos of every thing as you dissemble it, yes it is a pain to do but if you take photos reassembling you will have before and after photos to post on the forum.

09-12-17, 11:02 AM	#5
Rosco Newbie! Classic Audi Club Member Join Date: Oct 2017 Posts: 17	Thank you Dave and Colin for taking the time to reply, I nearly ordered the wrong ball joints. This forum is great!