Classic Audi Technical Mech/Tech Transmission » Clutch Slave cylinder removal

Reply
 
Thread Tools Display Modes
Old 18-05-19, 07:03 PM   #1
BackintheFold
Grown up member
Classic Audi Club Member
 
Join Date: Feb 2019
Posts: 435
Default Clutch Slave cylinder removal

Very frustrating morning.
I undid the bolt to remove the slave cylinder, but couldn't see a "retaining clip" referenced on Phil Paynes removal instructions. So I tried moving the cylinder and failed.

I've checked 7zap which doesn't show a retaining clip. Does anyone have a picture of what I'm supposed to remove please?
I'm thinking if I got the clip off the slave might move. Trying to drift it out from the engine bay will probably need two people-one below to line up the drift, one above to knock it back.
Thanks!
Oh-and the slave needs to be rotated clockwise (looking from the back of the car) about 30degtees or it can't be drifted backwards due to a "lip" on the gearbox.
BackintheFold is online now   Reply With Quote
Old 18-05-19, 07:43 PM   #2
Groundhog
Grown up member
 
Join Date: Nov 2009
Posts: 118
Default

If yours is held by a bolt it will not have a clip. The bolted type should come away easily, once the bolt is out just give the cylinder a lever sideways so the bolt flange clears the recess on the gearbox and it should simply drop away.
Groundhog is online now   Reply With Quote
Old 18-05-19, 08:06 PM   #3
tractor Dave
Grown up member
Classic Audi Club Member
 
Join Date: Apr 2018
Location: Wales
Posts: 516
Default

Over on the S2 Forum, Newsh has just posted a pic in his Ur thread which you may find helpful. Bottom of page.
https://www.s2forum.com/forum/member...project/page17
tractor Dave is online now   Reply With Quote
Old 18-05-19, 08:28 PM   #4
BackintheFold
Grown up member
Classic Audi Club Member
 
Join Date: Feb 2019
Posts: 435
Default

Thanks for those tips-the picture is good to see what the cylinder looks like in place, I'm not sure mine will fall out-but I didn't lever it too much, and what I did was vertical rather than horizontal.
Now I'm in a quandary. The car drives as is, and so I can take it to an mot to find out what else may need doing. If I get stuck with the cylinder I'll have to cancel the mot.
And I've only got evenings to work on it....outside...gamble time...
BackintheFold is online now   Reply With Quote
Old 18-05-19, 08:36 PM   #5
tractor Dave
Grown up member
Classic Audi Club Member
 
Join Date: Apr 2018
Location: Wales
Posts: 516
Default

It's easy for me to say sitting here with my glass of wine but I would crack on and change it. Sounds like you are already half way there and the weather isn't too bad at the moment. If it fails totally in rainy November you will regret not cracking on!

It's probably never been changed and the alloy corrosion has built up around where it fits and welded itself in. Spray the join with lots of WD40 or penetrating oil and leave it overnight. I'm sure it will pop out no problem tomorrow morning with fresh hands and new enthusiasm
tractor Dave is online now   Reply With Quote
Old 18-05-19, 09:01 PM   #6
BackintheFold
Grown up member
Classic Audi Club Member
 
Join Date: Feb 2019
Posts: 435
Default

Hahah! Yes. Easy to say...
I can't spare tomorrow to do it again. But it absolutely needs doing. I have to keep topping up the reservoir and the master 'seems' dry.
BackintheFold is online now   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT. The time now is 08:06 PM.

Powered by vBulletin®
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
Copyright ©2007-2008 Classic Audi | Site by Roadrunna