A80Q mileo dead?? - Page 2

spaarky · 08-08-09, 08:56 AM

Cheers Puglife, many thanks - am wading in the dark, all info much appreciated

Tommy WAT ? Dunno, but I think I'm gonna like the translation . . .

Ben · 08-08-09, 09:08 AM

As I've put before, be warned that the internals are different depending on what binnacle Audi put in your car, I had a cracked binnacle in my 80Q and tried to replace it with a good one from my spares car, an 80 sport, both cars were built in 91 and registered within a month of each other in early 92. To keep the mileage I tried to swap over the internals but they wouldn't fit, I then tried to swap just the speedo and it was COMPLETELY different and wouldn't fit either. I then stripped the speedo from the good binnacle to adjust the mileage and on trying the speedo didn't work

finally I took the binnacle from my B4 16V and put the innards from the 80Q, although the B3/B4 innards are different, the binnacle was the same design having VDO moulded into the plastic under the warning lights and what looks like the same speedo type with the number 893 190 printed on the front .

Top = German B3Q, middle = Japan B3 Sport, bottom = Malaysian B4 16V:

Puglife · 08-08-09, 09:31 AM

Thomas Wat on the school register............ T.Wat.

Ok small problem in that i dismantled this unit a while back to see how speedo was driven. The box its in has everything bar the geared wheel for odometer movement.... However you can see how it works from this. If i find the gear i'll get a photo and if yours is broken i'll pop it in post for £1....

From top to bottom the pins are:

Earth/Ground
31b
A
+15

spaarky · 08-08-09, 09:48 AM

yep, thought I'd like the translation, shame on me for not pickin it out - fantastic & thanks for your efforts - same goes for ben too - many thanks both of you, looks like it's now up to me to strip the bugger & see where we get - got a coupla fotos attached, not tried this before but hope you can see them, and understand why I'm spending the time. It's been so well looked after, & in the pass side door shut, I still have the factory bar code label . . .

spaarky · 08-08-09, 10:21 AM

just took these photos in the drive, but you can probly see why I don't wanna just throw her away:

msh · 08-08-09, 11:34 AM

Quote:

Originally Posted by Ben

Top = German B3Q, middle = Japan B3 Sport, bottom = Malaysian B4 16V:

Where did u get such mix?

Ben · 08-08-09, 12:10 PM

Quote:

Originally Posted by msh

Where did u get such mix?

Just lucky, I was refering to the manufacturing stickers on the back of the clocks, not from where the cars came from, I guess the cars were all made in Germany but for some reason they decided to design different binnacles that look the same for the same model of car

msh · 08-08-09, 12:15 PM

Reason must be very simple - more than one supplier. If there would be more than one supplier for KE-jet, then there wouldn't be a lot of problems...

Ben · 08-08-09, 01:17 PM

Quote:

Originally Posted by msh

Reason must be very simple

Ahhh.. I now have a voice to read your messages with

simples....

08-08-09, 09:31 AM	#13
Puglife ==>PUGSPORT!<== Classic Audi Club Member Join Date: Jan 2008 Location: Leyland Posts: 1,544	Thomas Wat on the school register............ T.Wat. Ok small problem in that i dismantled this unit a while back to see how speedo was driven. The box its in has everything bar the geared wheel for odometer movement.... However you can see how it works from this. If i find the gear i'll get a photo and if yours is broken i'll pop it in post for £1.... From top to bottom the pins are: Earth/Ground 31b A +15 __________________ 1986 UR Quattro - (1982) Lombard RAC Group 4 recreation - #24 H.Demuth/J.Daniels 1981 VW mk1 golf GTi - now 5cylinder and RWD.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
H from Steps is dead....	Coxy	General Chat	8	15-09-09 11:21 AM
Limey is dead! Help!	SteveCat	General Chat	15	10-08-09 01:42 PM
Mac G4 PSU dead	pimpdriver	General Chat	13	29-07-09 10:24 PM
Is everybody dead?	poopcoupe	General Chat	28	04-07-09 10:40 AM

08-08-09, 08:56 AM	#11
spaarky Grown up member Join Date: Oct 2008 Posts: 124	Cheers Puglife, many thanks - am wading in the dark, all info much appreciated Tommy WAT ? Dunno, but I think I'm gonna like the translation . . .

08-08-09, 09:08 AM	#12
Ben 4 ring whore! Classic Audi Club Member Join Date: Mar 2008 Location: Stockport Posts: 2,348	As I've put before, be warned that the internals are different depending on what binnacle Audi put in your car, I had a cracked binnacle in my 80Q and tried to replace it with a good one from my spares car, an 80 sport, both cars were built in 91 and registered within a month of each other in early 92. To keep the mileage I tried to swap over the internals but they wouldn't fit, I then tried to swap just the speedo and it was COMPLETELY different and wouldn't fit either. I then stripped the speedo from the good binnacle to adjust the mileage and on trying the speedo didn't work finally I took the binnacle from my B4 16V and put the innards from the 80Q, although the B3/B4 innards are different, the binnacle was the same design having VDO moulded into the plastic under the warning lights and what looks like the same speedo type with the number 893 190 printed on the front . Top = German B3Q, middle = Japan B3 Sport, bottom = Malaysian B4 16V:

08-08-09, 12:15 PM	#18
msh 4 ring whore! Join Date: Jun 2008 Location: Rucava, Latvija Posts: 3,816	Reason must be very simple - more than one supplier. If there would be more than one supplier for KE-jet, then there wouldn't be a lot of problems...